20 bucks. At least, that's what I remember them going for at the boat anchor salvage yard. :)

Puurrrdy.

Man you could fit a small deer in that thang!

Coupon code today is "LBL"....good for another 20.00 off


http://www.brownells.com/rifle-parts/receiver-parts/receivers/upper-receivers/ar-15-upper-receiver-w-lower-parts-kit-stock-assembly-sku080001326-88056-190557.aspx?sku=080-001-326

Nice score Nate!

What did you use to cut the foam?

lol

I found this on the ATF site:



To whom may an unlicensed person transfer firearms under the GCA?


A person may transfer a firearm to an unlicensed resident of his or her State, provided the transferor does not know or have reasonable cause to believe the transferee is prohibited from receiving or possessing firearms under Federal law. There may be State laws that regulate intrastate firearm transactions. A person considering transferring a firearm should contact his or her State Attorney General’s Office to inquire about the laws and possible State or local restrictions.

Generally, for a person to lawfully transfer a firearm to an unlicensed person who resides out of State, the firearm must be shipped to a Federal firearms licensee (FFL) within the transferee’s State of residence. The transferee may then receive the firearm from the FFL upon completion of an ATF Form 4473 and a NICS background check.

A person may loan or rent a firearm to a resident of any State for temporary use for lawful sporting purposes, if he or she or she does not know or have reasonable cause to believe the person is prohibited from receiving or possessing firearms under Federal law. Another exception is provided for transfers of firearms to nonresidents to carry out a lawful bequest or acquisition by intestate succession. This exception would authorize the transfer of a firearm to a nonresident who inherits a firearm under the will of a decedent.

A person may transfer a firearm to a licensee in any State. However, a firearm other than a curio or relic may not be transferred interstate to a licensed collector.

[18 U.S.C 922(a)(5) and 922(d); 27 CFR 478.30, 478.32]


It also appears that even if you have to go the ffl route, it's only on the receiving end.

Makes sense. I saw where they were welding lips on the top and bottoms as well. I'd be worried about my welds !

Yeah. there's another company that started that a while back....I remember seeing the videos on youtube. Icr how many coats they put on, but it does work. I think it also helps a little with penetration because it absorbs some of the initial impact.

Tex, for you or the kids? I wonder sometimes which would be easier. lol

I don't know if I have the patience to "properly" break in a barrel.

You think running 2-100 round drums through it would do the trick?

Sandblasted and coated one ar15 and one ar10 lower, let tack, found flaws, tried to clean off Cerakote with thinner and failed, resandblasted, getting ready to try again.

If you have a strong wrist, a boxcutter will give the cleanest line. A cutoff wheel/die grinder or an oscillating tool will also work.

That. Is. Way Cool.

Nice one to go with Don.

I personally jack the truck up before cranking on the bolts....less stress on them. Oh, and mark them so you can count the turns and keep them even.

Awe heck. The oil came from the ground, I feel that's it's only our duty to put it back there!

jk, but for what it's worth, my shop is septic, and washing our nasty hands 20 or more (2-3 people) times a day for several years hasn't affected it. The bacteria is stronger than Zep hand cleaner I guess....but...I also keep straight chemicals/oil out of the sink.

Wow. Just wow Kyle. Seriously, good for you

..that sucker will be stout!

... I see the rolling tool bin there to the right is still in the same place..... ;D

I was wondering what that was, holding up that handyman jack. hehe

I second the motion!

Weez gots impotent thangs to discuss overhere!

Shawn, that seems like overkill for a 7k trailer. Just sayin'. I know you like to do things overkill (as well do I) but the idea is to be able to haul the heaviest weight with the least amount of trailer weight as possible and still be safe. I'll weight for your lashing. :)


18' is a perfect length car hauler imo. I've used the 3 common ones quite a bit..16, 18, and 20. the 20 always drags...always. The 16 is short for hauling trucks. The 18 will fit our trucks and still have room for movement.

Again, just my opinions.

..... given the silent majority whose temperature is rising and nearing the boiling point.


Sent from my iPad using Tapatalk

I agree completely. We tend to only hear from the outspoken people, the ones full of hot air, the liberals, until the right buttons get pushed.

hahaha

Yeah. Use a trough with 1/4" teeth (most common), lay it at a 45*, and scrape, keeping all the grooves in the same direction. This allows (helps) trapped air to escape from under the tile.

...and you keep the mud just thick enough to where the ridges that you create with the trough, don't just slump out, but not so thick that the tile doesn't want to compress the air out from underneath.

You pulling All of the tile? I have a little experience with tile. It's a little hard to do door jams without a saw, but laying tile is a remedial job at best.....ie...If i can do it, you can do it! hardest part is keeping them level..make the mud too thick, they won't "mallet" down, too thin, and they "fall" lower than the surrounding ones.
Chalk line it out to keep them straight, and pre-lay some in the middle to make sure it will work out.Oh, and knee pads are a must!

Maybe I should've been more specific..."speaky da Englisho" 



(french canadian :) )

Everytime I do that I end up peed off.  No one in this town knows how to properly detail  (nor speak English )

Sent from my SM-G900V using Tapatalk