0 Members and 117 Guests are viewing this topic.
I just don't want to wind up missing a digit or limb. I can sometimes get in a hurry to get results.
Dunno on the glow plug Dave. Doesn’t make sense that it would be a dud. Could be a bad wire. I’m actually quite scared for the project I’m in the middle of for bad broken wires. I think I have the motor ready to pull. Nine aweful trans bell housing bolts out. Six ridiculous to access torque converter bolts out. All six bazillion ground points off. Six motor mount bolts left. Insert trans jack cause it looks like it’s gonna fall. Jerk the LBZ free. Sent from my iPhone using Tapatalk
I don’t know how you keep all the hardware straight. I also don’t know how ya can do that in a timely manner. I can’t finish a project no matter how small lol dirt bike in parts, ATV in parts, enclosed partially done, flatbed conversion rusting away. Yeah I’m not sure I’ll have to do some wire searching see what I can chase down. It’s not a two ware plug its just a single eyelet and I think beaded wire isn’t it? Sent from my iPhone using Tapatalk
One last question for the group PO677 code, glowplug ok got it, changed it. Still having same code. Suggestion? Thoughts? Did the dealer sell me a bad glowplug? Does that happen? Sent from my iPhone using Tapatalk
I’m pretty sure I did, the driver side next to the firewall right? Sent from my iPhone using Tapatalk
Quote from: Bigdave_185 on July 21, 2021, 12:08:13 AMI don’t know how you keep all the hardware straight. I also don’t know how ya can do that in a timely manner. I can’t finish a project no matter how small lol dirt bike in parts, ATV in parts, enclosed partially done, flatbed conversion rusting away. Yeah I’m not sure I’ll have to do some wire searching see what I can chase down. It’s not a two ware plug its just a single eyelet and I think beaded wire isn’t it? Sent from my iPhone using TapatalkHardware goes back in the hole it came out of, or in a labeled ziploc bag. Wiring connectors get a “toe tag”, but only if you’re OCD like me :D
That makes for a rough camp with a peeed in sleeping bag Other boys get after him or did it stay quiet??Sent from my iPhone using Tapatalk
Quote from: Bigdave_185 on July 21, 2021, 10:33:10 AMI’m pretty sure I did, the driver side next to the firewall right? Sent from my iPhone using TapatalkThen you did #8. Sorry to be the bearer of bad news. Probably have a good glow plug in the garbage if the nut threaded off.
I could bring home a 1” bohemoth but that seems like overkill. My Milwaukee is 1100 ft/lbs. breaking torque. This is the first thing it couldn’t break or loosen. 2862 M18 FUEL, for anyone that is interested. They have a bigger one now too. I’ll do a heat soak to break down the loctite. If that doesn’t work I’ll have to get mean.
Quote from: Sammconn on July 22, 2021, 03:06:38 PMI could bring home a 1” bohemoth but that seems like overkill. My Milwaukee is 1100 ft/lbs. breaking torque. This is the first thing it couldn’t break or loosen. 2862 M18 FUEL, for anyone that is interested. They have a bigger one now too. I’ll do a heat soak to break down the loctite. If that doesn’t work I’ll have to get mean.I have one also, but still doesn't hit as hard as air ....or it hits different. Can't explain it
Discovered this handy little guy. Sent from my Pixel 5 using Tapatalk
Ken’s gf: “1400 lb of NUT BUSTING torque” they advertise on the website. LOL
Quote from: Farmer Jon on July 22, 2021, 05:48:51 PMDiscovered this handy little guy. Sent from my Pixel 5 using TapatalkCan’t tie a tautline hitch?
Drove 750 miles from Maud Ok to Firestone CO. My backside is numb and people around Denver don't know how to drive in the rainSent from my SM-N975U using Tapatalk
Quote from: oklawall on July 23, 2021, 08:19:28 AMDrove 750 miles from Maud Ok to Firestone CO. My backside is numb and people around Denver don't know how to drive in the rainSent from my SM-N975U using TapatalkMy shop is ten minutes from Firestone, you should stop by.
I see the flex plate is off. Howd that go?Sent from my iPhone using Tapatalk
Got to put a face to user name. Neet Shawn and Norm at Shawn shop. All around a great daySent from my SM-N975U using Tapatalk
Quote from: oklawall on July 23, 2021, 04:58:14 PMGot to put a face to user name. Neet Shawn and Norm at Shawn shop. All around a great daySent from my SM-N975U using TapatalkNo picture of proof huh ? Sent from my iPhone using Tapatalk
Quote from: TexasRedNeck on July 23, 2021, 04:12:40 PMI see the flex plate is off. Howd that go?Sent from my iPhone using TapatalkWell, the red wrench and my impact. No beuno. Red wrench, flywheel lock, big Johnson bar. No beuno. Add my buddy and a 36mm on balancer bolt to counteract the force on three and voila. Not done alone for me. Watched some YouTube and got that idea.