Hello Guest

Recent Posts

Pages: [1] 2 3 ... 10
1
Hide Site / Re: Raptor Ridge, the build.
« Last post by JR on Today at 01:56:30 AM »
I have ether, but just got an air tank seater. Not as fun but simple. probably need to pull off and clean the bead area, still rough after the flood.
2
Hide Site / Re: Raptor Ridge, the build.
« Last post by Flyin6 on May 07, 2024, 04:17:35 PM »
I meant ether and match to set the bead on the tire…


Sent from my iPad using Tapatalk
"Breck" hair spray works pretty well too
and
It's the primary fuel for your potato gun ;-)
3
Firearms / Re: Birthday gun
« Last post by Flyin6 on May 07, 2024, 04:15:56 PM »
10mm is just a longer 40 cal.  Same dies.

Actually the 10mm came first, then the limp wristed FBI folks couldn’t deal with the recoil so they started down loading it and realized they didnt need all the cartridge length….and the 40S&W was born…


Sent from my iPad using Tapatalk
1. They're listening, ya know...
2. You're not making any friends over in Quantico
3. We all are probably on some list
4. There's likely no one over there who is vindictive...:-0
4
Everything Trailer, Camper, or RV related / Re: Don's 2024 Palmino 3210 Camper
« Last post by Flyin6 on May 07, 2024, 04:13:21 PM »
This has turned out to be an interesting story

Holman motors completed all repairs yesterday except for the slide's awning, which had not come in yet.

THey asked me to come pick up the camper and just bring it back when the awning came in. So I motored up there yesterday to pick it up as requested. After arriving, I got to inspect the work, which was excellent, and it looks better than when I purchased it. But something was not finished which the tech noticed, so I was sent home to come back today.

I did that, arriving before 0900. While awaiting them to marry up the camper to my truck once again, the brown truck showed up and guess what was inside??? My new awning!

So they sent me home with a rental/loaner and kept the dually. I guess I'll go pick it up tomorrow and be back up to 100%.

That's great because when the bumper is bolted onto the Ram, the truck will be mission-ready, and work will shift to the camper. It will get loaded with all the essentials while I figure out what that looks like.

I own a 2K HF generator that is whisper quiet, so I'm contemplating getting a generator box and bolting all that to the backend. I think I will add a second LIPO battery because people who have boondocked for over a week in my model camper, advise that 200 amp/hr. of lithium will carry all your needs. They carried a small gas generator to top up the batteries when it was cloudy, so I think I'll prep in the same manner.
I also plan to add a soft start capacitor to the AC unit and perhaps another one to the outlets circuit. That should allow me to run the AC and a coffee machine on a 2K generator.

Also on the list is a ladder, a cell phone booster, and the Star Link antenna with a roaming plan.
5
Build Threads / Re: Don's 2024 Ram 3500
« Last post by Flyin6 on May 07, 2024, 03:58:47 PM »
Divide your new tire height by the old tire height. That will give you the percentage you are off.


Sent from my iPad using Tapatalk
Copy that...4%

33.1/31.8=1.04xxx

65 indicated X 1.04 = 67.6
70 indicated X 1.04 = 72.8

Closer than I thought

...And thanks
6
Build Threads / Re: Don's 2024 Ram 3500
« Last post by JR on May 07, 2024, 02:26:00 PM »
I just verify with my phone. 4mph under at 70 for dmax, tahoe is dead on.
7
Firearms / Re: Birthday gun
« Last post by TexasRedNeck on May 07, 2024, 01:57:53 PM »
10mm is just a longer 40 cal.  Same dies.

Actually the 10mm came first, then the limp wristed FBI folks couldn’t deal with the recoil so they started down loading it and realized they didnt need all the cartridge length….and the 40S&W was born…


Sent from my iPad using Tapatalk
8
Build Threads / Re: Don's 2024 Ram 3500
« Last post by TexasRedNeck on May 07, 2024, 01:55:33 PM »
Divide your new tire height by the old tire height. That will give you the percentage you are off.


Sent from my iPad using Tapatalk
9
Hide Site / Re: Raptor Ridge, the build.
« Last post by TexasRedNeck on May 07, 2024, 01:53:13 PM »
I meant ether and match to set the bead on the tire…


Sent from my iPad using Tapatalk
10
Hide Site / Re: Elbow Room
« Last post by Flyin6 on May 07, 2024, 08:54:32 AM »
Someone say pond and zero turn???


Sent from my iPad using Tapatalk
;-)
Pages: [1] 2 3 ... 10
SimplePortal 2.3.6 © 2008-2014, SimplePortal