This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - JR
Pages: 1 ... 199 200 [201] 202 203 ... 270
10001
« on: September 29, 2016, 11:04:01 AM »
Looks great.
10002
« on: September 29, 2016, 10:54:34 AM »
I have those on my chimney, same design I think? Would like to add them on the exposed foundation around my house.
10003
« on: September 29, 2016, 09:59:23 AM »
I take it it there will be cultured stone below the trim?
10004
« on: September 28, 2016, 11:30:07 PM »
Way to nice, I'll take it.
10005
« on: September 28, 2016, 09:41:27 PM »
Did you drive inside and lift it by the center?
10006
« on: September 28, 2016, 07:56:45 PM »
I like the setup and you've given me a new idea on mounting mine.
10007
« on: September 28, 2016, 05:40:23 PM »
Be careful what you wish for,,,,,,,,,,,,,
10008
« on: September 28, 2016, 01:16:28 PM »
That'll slow you down for a few, but sure leaves some opens up some prime commentary,,,,,,,,,,,,,,,,,
10009
« on: September 28, 2016, 01:12:26 PM »
Looks great.
10010
« on: September 28, 2016, 01:16:19 AM »
Spray and prey??
10011
« on: September 27, 2016, 02:30:36 PM »
One less thing to do and what would it hurt?
I like using simple green to clean muck like that..
10012
« on: September 27, 2016, 10:10:57 AM »
Went and did some logging with the tuner and his laptop on my pickup truck. Seems to be as he called it surging. Not anything else visible in the file to suggest why. So I will start at the fass fuel pump and see what pressure that is giving the cp3. Then might look at replacement of the cp3
Sent from my iPhone using Tapatalk
Thats the trouble with these things. So many sensors and this works off of that. CPS won't be cheap but good to get the issue fixed.
10013
« on: September 27, 2016, 12:24:48 AM »
That looks pretty clean for a pull out.
10014
« on: September 25, 2016, 11:43:47 PM »
I know, just share the misery,,,,,,,,,,,,,,,
10015
« on: September 25, 2016, 11:16:18 PM »
Good luck, take lots of pics for us.
10016
« on: September 25, 2016, 11:34:31 AM »
Video, much better than pics!!
10017
« on: September 25, 2016, 01:26:07 AM »
You know the rules....pics?
Sent from my iPhone using Tapatalk
10018
« on: September 25, 2016, 01:24:58 AM »
Yep, EFILive. I don't tune either but having issues with new firmware. I adjust some settings and always loaded through the flashscan.
I can only program using the old "tun" not the "CTZ" it all converts to now. Been reading my but off, but have not got the flashscan to program alone.
Right now I have a 100/230 tune running, but it is touchy at low throttle. It gets great mileage though. I have a DSP5 by IdahoRob, but running his 100hp never felt this solid or got the mileage.
I talked to Dave a little tonight and will probably call Rob this next week.
10019
« on: September 25, 2016, 01:14:39 AM »
Total cost for a little over 1600 miles was $230 bucks
20 mpg is great, but didn't you forget one little expense?
10020
« on: September 24, 2016, 06:21:04 PM »
Nice looking, cept the Ken rockers,,,,,,,,,,,,,,,,,
Ken, you an EFI guy at all?
10021
« on: September 24, 2016, 03:58:44 PM »
To bad I just saw this. Did you have em check the Tcase for the rub. Would have been a great time for it laying on the bench.
Was that PSI pulling a hill? I cruise at around 4-5 and only see that when really on it.
Ouch, 5k for the rebuild, glad I haven't hurt the tranny yet. However having issues with EFI but got a 100/235 tune in there now.
10022
« on: September 24, 2016, 03:34:05 PM »
Hockey pucks?
10023
« on: September 24, 2016, 03:32:44 PM »
Aw, just JB it and go,,,,,,,,,,,,,
10024
« on: September 24, 2016, 04:24:43 AM »
Come on, lets see some pics!!!!
10025
« on: September 24, 2016, 04:21:19 AM »
Glad to see an update. I think Spartan is going just as fast,,,,,,,,,,,
10026
« on: September 23, 2016, 10:37:09 AM »
I am seriously leaning towards just running the service, and doing 1 light and 1 gfi outlet and calling for inspection. Then get final, and then start pulling wire
Sent from my iPhone using Tapatalk
That's a good plan!
I agree, but check if there is a minimum for outlets.
10027
« on: September 23, 2016, 10:12:37 AM »
...And, what a cool breakfast idea!
Have to agree,,,,,,,,,,,,,,
10028
« on: September 22, 2016, 05:38:37 PM »
Yep, did a lot of that in my garage too. You may want to check on the ply/osb though as they may not deem that good fire retardant wall cover.
Now if you haven't done the wiring, just get the conduit, not really much more $$ then you can upgrade when you want.
10029
« on: September 22, 2016, 02:41:34 PM »
Sheetrock saved my house back in 06 when I had a garage fire. Worse damage was the FD with cutting holes all over the roof and all the water!
10030
« on: September 22, 2016, 10:41:29 AM »
Thx, she is the band, cross county and has the homecoming dance this weekend. No boys yet, but I know they are looking!
10031
« on: September 21, 2016, 02:58:49 AM »
Let them think it was women, nice little twist.
10032
« on: September 21, 2016, 12:55:30 AM »
But of course with lots of pictures!
10033
« on: September 21, 2016, 12:33:52 AM »
I have seen good 5hp motors for $200, then $240 for the pump. Wiring and fittings at least $100.
10034
« on: September 21, 2016, 12:31:02 AM »
A 60 is fine for almost anything up to blasting or sanders. Depends on the sander but blasting uses alot of CFM.
Impacts, nailers and such are no big deal. Heck my little 8gal 2hp does that.
10035
« on: September 21, 2016, 12:23:14 AM »
All sanded down and ready for sealer sans the one step with the wires. I need to drill another hole and relocate them over some.
I was ready to sheetrock the opening and I found a slight issue. The second step to the door opening is just 72 inches, not quite enough for not knocking the head for sure!
So now I have to remove the lip and re-route several wires in there. That gains me almost 4 inches and even more if I angle it a little. However this means I need to put a 4x6 over the doorway so it will be supported. I will box in the opening above the stairs, but leave the rest open. That works fine as the router is located up there and it gives a nice spot to get it out of the open.
10036
« on: September 20, 2016, 05:35:33 PM »
Been there done that, thank GOD it was just 5ft up. Screwed up my leg on a step though.
10037
« on: September 20, 2016, 03:48:43 PM »
Who driving the truck??
10038
« on: September 20, 2016, 03:45:08 PM »
Awe, we sure are. She is 5-8 right now and the older boy looks just like my brother who he is named after. (passed away)
That was the first day of school for them this year so its not a total DOT post.
10039
« on: September 20, 2016, 02:41:43 PM »
Maybe a motion for 1 light in each shop and a switch for the rest. Plus the motion helps lets you know if someone is there when you aren't minus an alarm.
You could also just run the light runs all to one box and modify as seen by use.
10040
« on: September 20, 2016, 01:30:35 PM »
She sure looks like you. Did I ever tell you how cute you are???
I have no idea where my daughter got her looks from,,,,,,,,,,,,,,,,,,plus the $7000 smiles!!
10041
« on: September 20, 2016, 10:36:00 AM »
I am putting the 9.5 into my 91 flip suburban. It has the 8.5 stock and they blow like crazy. The HD will have 8 lugs though and even the 6 lug may have 14mm vs 1/2 studs.
10042
« on: September 20, 2016, 01:44:40 AM »
Just don't put another 8.5 under there if you have that. Go right to the 9.5, they seem to be way better and should be a bolt in.
10043
« on: September 20, 2016, 01:40:56 AM »
I have a couple of those, they work great. One over the lathe and the other in the shed, nice when cold as the LED works more better than flo's.
I have been looking for flat panels or recessed for up stairs, but nothing has grabbed yet.
10044
« on: September 20, 2016, 01:33:34 AM »
10045
« on: September 19, 2016, 02:49:24 PM »
More air storage is where it is at. I have a 5hp-80 with 175psi thats US made. Its quiet and its motor is twice the size of the box store stuff.
Not sure if you are thinking about it, but do not even think of oil-less.
10046
« on: September 16, 2016, 11:31:03 PM »
Looks good Kyle.
10047
« on: September 16, 2016, 11:01:41 PM »
Sounds like a time. Guns and friends.....................
Isn't Chicago a gun free zone, good luck!!
10048
« on: September 16, 2016, 11:44:16 AM »
Well Tate, thats why we went with the 4.56 then. On the table soon, playing with tunes again.
What was this thread about???????
10049
« on: September 16, 2016, 10:02:08 AM »
I have 4.56 for mine as 410 seemed a little low, but 4.30s are not there.
Funny how the 35 tire just measures 33 at rest! I was guessing 34.5 or similar and there is still lots of tread.
Yes he is.
10050
« on: September 15, 2016, 10:44:28 PM »
Most of my driving is around town and the mileage is lousy, like Kens.
I am thinking of loading a 120hp tune I have. My normal was a 100hp from Rob, but mileage was never really good and EGTs seem a little high.
Pages: 1 ... 199 200 [201] 202 203 ... 270
|
Show Posts
