0 Members and 2 Guests are viewing this topic.
I just don't want to wind up missing a digit or limb. I can sometimes get in a hurry to get results.
A loose lug nut? ;)
sell it to me for $1 and go get yourself something that works...... ;-0
That old Case still keeping up with the workload?
It has a quality 0-3000 psi gage, glycerin filled, mind you. He attached the proper ends to six feet of 5800 psi hose and clamped it all together.Time to break something else!
Quote from: Flyin6 on October 03, 2017, 07:36:32 PMIt has a quality 0-3000 psi gage, glycerin filled, mind you. He attached the proper ends to six feet of 5800 psi hose and clamped it all together.Time to break something else!FIFY
OK, task one and two complete.First, get the instructions to start the testing procedureLarry, Jon, and Richard hooked me up on that front.Next was find a hydraulic test gage. I just went over to Fluid and Air and talked to Kenny who wipped me up a test gage for $69 and sent me packin'After the Ortho appointment tomorrow, I should be cleared for flight to head down farmside and hook this contraption up to my ailin' Sergeant.
Quote from: rpar86 on October 03, 2017, 07:49:01 PMQuote from: Flyin6 on October 03, 2017, 07:36:32 PMIt has a quality 0-3000 psi gage, glycerin filled, mind you. He attached the proper ends to six feet of 5800 psi hose and clamped it all together.Time to break something else!FIFYYou been fired or banned yet? ;-))
Quote from: Flyin6 on October 03, 2017, 07:50:50 PMQuote from: rpar86 on October 03, 2017, 07:49:01 PMQuote from: Flyin6 on October 03, 2017, 07:36:32 PMIt has a quality 0-3000 psi gage, glycerin filled, mind you. He attached the proper ends to six feet of 5800 psi hose and clamped it all together.Time to break something else!FIFYYou been fired or banned yet? ;-))Easy, I must be getting soft...... I reworked a whole paragraph last night and even fired myself like twice to turn around and just delete it all. Expensive equipment failures bring the suck, you have my condolences!
Well with any luck you just need to adjust the relief valve and be back on the go.
I read about a power screw. Turning it clockwise, five degrees at a time adjusts the smoke (Power) Now I have never seen anything hurt from a little extra power...
So, Bobby...being the calculating trained warrior NCO that you are. Take the appropriate action, Execute!
your standard grunt level CQB is just putting rounds and rounds on scary stuff till it stops scaring you!
Quote from: Flyin6 on October 04, 2017, 11:07:41 AM I read about a power screw. Turning it clockwise, five degrees at a time adjusts the smoke (Power) Now I have never seen anything hurt from a little extra power...Didn't you turn the screw on Square D, and now....
Quote from: Sammconn on October 03, 2017, 08:58:23 PMWell with any luck you just need to adjust the relief valve and be back on the go.That's what I am hoping for tooYa know, lookin' over the manual. at the Robert Bosch injection pump section, I read about a power screw. Turning it clockwise, five degrees at a time adjusts the smoke (Power) Now I have never seen anything hurt from a little extra power...
Quote from: Flyin6 on October 04, 2017, 11:07:41 AMQuote from: Sammconn on October 03, 2017, 08:58:23 PMWell with any luck you just need to adjust the relief valve and be back on the go.That's what I am hoping for tooYa know, lookin' over the manual. at the Robert Bosch injection pump section, I read about a power screw. Turning it clockwise, five degrees at a time adjusts the smoke (Power) Now I have never seen anything hurt from a little extra power...Without a pyro I'd be very cautious of this. I dabbled a couple times back in the day on an old 3406 Cat in a semi. There comes a point where you will give too much, and if Sarge doesn't have a pyro you won't know.
HEY BIG D, PLEASE DONT TOUCH THE SCREW!!!!!!!!! TALK TO LOCTITE AKA RICHARD FIRST....
Quote from: DOOLEY on October 04, 2017, 04:17:45 PMHEY BIG D, PLEASE DONT TOUCH THE SCREW!!!!!!!!! TALK TO LOCTITE AKA RICHARD FIRST....Ah, man...You're killin my fun here!
Quote from: DOOLEY on October 04, 2017, 04:17:45 PMHEY BIG D, PLEASE DONT TOUCH THE SCREW!!!!!!!!! TALK TO LOCTITE AKA RICHARD FIRST....Someone else who knows the dangers of Don screwing with stuff he just shouldn't
Any update on what's ailing Sarge?
Quote from: Tommy13 on October 17, 2017, 11:03:56 AMAny update on what's ailing Sarge?Usually officers getting into NCO business...