Author Topic: Dawg's Shop (Read 27251 times)

Dawg25385 · « **on:** March 29, 2017, 01:51:36 PM »

Going to start an exclusively shop related thread. Lots going on down there now, so figured what the heck.

Here goes!

JR · « **Reply #1 on:** March 29, 2017, 02:03:39 PM »

Bob Smith · « **Reply #2 on:** March 29, 2017, 02:05:44 PM »

When I get back home, I plan on coming over and check it out

Dawg25385 · « **Reply #3 on:** March 29, 2017, 02:06:41 PM »

So i'm starting to tool my shop. Predominantly woodworking, but I have also inherited a oxy/acetalyne torch and a Lincoln tombstone welder that i'll have setup at some point.

Got this drill press from my dad, i think i posted elsewhere where i cleaned it up. I built this stand for it on casters. You'll find that one of the themes for the woodshop and things i build as far as organization/carts/etc... i don't want to see any fasteners. So i'll be using more half-lap joinery, mortise and tenon, dados, etc. And pocket-holes if i need to use screws. Here's the stand for the drill press

Also picked up this Dust Collector. Will ultimately build a 2-stage cyclone setup, but this is a 2HP, 1700 CFM unit from Grizzly. Runs on 220, so i'm wiring up the shop with 220 plugs here and there to future proof for 'bigger' tools as well (planer/jointer/table saw/etc).

Also picked up insulation and sheeting for the double bay. This will go up as soon as wiring is done, next couple weeks.

Next, I built some clamp racks for my growing collection of Bessey clamps. First i started by laminating some 3/4 AC ply

Then i cut grooves for the bars. Did this by drilling holes on the drill press, then hogging out the material with the table saw

Used some scrap material to create this for Quick Clamps and spring clamps

Here they are together. Once the walls are insulated and sheeted, i'll probably put these on french cleats on this wall so they're more modular, and moveable

Lots more coming up!

Dawg25385 · « **Reply #4 on:** March 29, 2017, 02:08:18 PM »

You guys are always welcome!

Dawg25385 · « **Reply #5 on:** March 29, 2017, 02:10:23 PM »

From my other thread, here's the table saw I picked up recently. It's the hybrid by Ridgid. Pretty happy with it so far

I got a whole bunch of new tools that I'll try and share some pics of also. Heck maybe I'll go snap some pics now!

Sent from my iPhone using Tapatalk

Dawg25385 · « **Reply #6 on:** March 29, 2017, 03:00:27 PM »

We wanted to declutter the garage a little, and also get the "trailer stuff" closer to the trailer, so I insulated and sheeted this section and then built some shelves. This stuff is used for camping, tailgating, etc, so it made sense to have it so close to the RV

And here's my wood storage for now. All of this will get used in the coming month or so for various projects

New tools!!

My framing nailer went bad, so I splurged and picked up this new Ridgid

And also a new Brad nailer

And shoot, why not a new palm router

The Ridgid lifetime service agreement is why I have been choosing Ridgid tools in addition to my normal DeWalt fanboy bias, and it helps that most of these that I've purchased have been on sale

Sent from my iPhone using Tapatalk

Dawg25385 · « **Reply #7 on:** March 29, 2017, 03:02:15 PM »

Splurged also an got a nice Forstner bit set from Rockler for the drill press

And also a new Dremel, since my previous chinaman WEN p.o.s. crapped out mid project

Sent from my iPhone using Tapatalk

JR · « **Reply #8 on:** March 29, 2017, 03:03:48 PM »

You are splurging! Any rigid 12v stuff?

Dawg25385 · « **Reply #9 on:** March 29, 2017, 03:06:40 PM »

Quote from: JR on March 29, 2017, 03:03:48 PM

You are splurging! Any rigid 12v stuff?

Nope, all of my cordless stuff is DeWalt

Bob Smith · « **Reply #10 on:** March 29, 2017, 03:11:58 PM »

Wow birthday gifts come early

Dawg25385 · « **Reply #11 on:** March 29, 2017, 03:21:54 PM »

It's a long story, and don't really want to get into the details, but i got a little bit of excess spending money for the shop. Nobody died, don't worry

Bigdave_185 · « **Reply #12 on:** March 29, 2017, 03:29:45 PM »

Did you rob those Wells Fargo banks in New Mexico? Seen that on the news the other day

Sent from my iPhone using Tapatalk

TexasRedNeck · « **Reply #13 on:** March 29, 2017, 03:52:18 PM »

I loaned my framing nailer to my dad. So now I'm looking for a new one. What did you look for in your nailer?

Sent from my iPhone using Tapatalk

Dawg25385 · « **Reply #14 on:** March 29, 2017, 03:58:09 PM »

Weight was a big factor, the Ridgid has a Mg bell housing so it's light... needed to shoot short 2" nails well as well as full size sinkers, since i use 2" galvy ring shanks for fencing. Ridgid does both really well. Feels great in the hand, has a nice rafter hook that you can loop on your bags too if on a ladder or whatever. The depth adjustment is super slick too, very easy even with gloves on. Got great reviews online as well from pros. This is the 'new' Ridgid. The previous model did have issues feeding short nails, so stay away from that one. It came down to this one and a Hitachi, which is kind of the standard around here. Every framing crew you see will be running Hitachi.

And the kicker was the LSA (lifetime service agreement), which beyond the mfg warranty will cover failure outside of abuse.

TexasRedNeck · « **Reply #15 on:** March 29, 2017, 05:11:08 PM »

Thanks dawg. What model number?

Sent from my iPhone using Tapatalk

Wilbur · « **Reply #16 on:** March 29, 2017, 05:38:04 PM »

That is awesome! Nice job!

Flyin6 · « **Reply #17 on:** March 29, 2017, 07:00:40 PM »

Good work everywhere!

I can't decide if I like the drill press table or the racks for the clamps more at this point. Both are pretty cool!

Dawg25385 · « **Reply #18 on:** March 29, 2017, 08:02:50 PM »

Quote from: TexasRedNeck on March 29, 2017, 05:11:08 PM

Thanks dawg. What model number?

Sent from my iPhone using Tapatalk

It's the R350RHF

Sent from my iPhone using Tapatalk

Dawg25385 · « **Reply #19 on:** March 29, 2017, 08:04:27 PM »

Quote from: Flyin6 on March 29, 2017, 07:00:40 PM

Good work everywhere!

I can't decide if I like the drill press table or the racks for the clamps more at this point. Both are pretty cool!

Lots more projects like that in the works....

Dedicated miter saw station, cordless drill rack and charging station, finish nailer rack, etc...

Stay tuned!

Sent from my iPhone using Tapatalk

rpar86 · « **Reply #20 on:** March 30, 2017, 02:41:30 AM »

Looking great Kyle! Loving the additions and projects you've built thus far.

cruizng · « **Reply #21 on:** March 30, 2017, 09:28:26 AM »

WAY too organized!! How do you find anything unless it's under some pile?

Very nice!

Flyin6 · « **Reply #22 on:** March 30, 2017, 09:30:33 AM »

Quote from: cruizng on March 30, 2017, 09:28:26 AM

WAY too organized!! How do you find anything unless it's under some pile?

Very nice!

He'll get there

He just doesn't have enough stuff (junk) yet!

Maybe a quick visit to Norm's place and he can get a few piles...

KensAuto · « **Reply #23 on:** March 30, 2017, 09:45:07 AM »

Great craftsmanship Kyle. I love doing woodwork, only second to metalcraft.

Sent from a spaceship

Dawg25385 · « **Reply #24 on:** March 30, 2017, 11:58:25 AM »

It's kind of a mess right now, as I'm in a state of flux with a lot of my tools living up in the garage until everything gets moved down to the shop.

Sent from my iPhone using Tapatalk

Dawg25385 · « **Reply #25 on:** March 30, 2017, 11:17:19 PM »

One little shop project today, weather was so nice I tried to take advantage of it and work outside.

But, today I put a decent blade on my miter saw, Diablo thin kerf 60 tooth. And, fabbed a zero clearance plate as well. Lots of detail you can't see. Had to rabbet the underside edges, and routed out recesses for various things underneath, since I made it out of 3/4" ply

See the difference, the red inserts were factory, and flimsy plastic at that

For those who have no idea why you'd want zero-clearance inserts, this way the workpiece is supported right up to the cut line, so you get less tear out. Really only matters for precision cuts... could care less for framing material

Sent from my iPhone using Tapatalk

JR · « **Reply #26 on:** March 31, 2017, 12:02:06 AM »

Heck the thin blade and 60t is just a nice upgrade. Zero clearance is even better. Will it work on bevel cuts?

My new Kobalt saw went threw the first blade in like 10 cuts, must have hit something. Put a 40t Diablo on it and smooth as silk.

Dawg25385 · « **Reply #27 on:** March 31, 2017, 12:05:02 AM »

I can cut through the plate if I need to for beveled cuts, but in truth I've never use that functionality.

I put a 50 tooth combination Diablo blade on my table saw and it's money... the diablos are great value

Sent from my iPhone using Tapatalk

Dawg25385 · « **Reply #28 on:** April 26, 2017, 04:20:17 PM »

Been battling a wicked cold since getting back from vacation, but finally could get some work done on the shop.

Insulation... my favorite.

Sheeted this corner so I could get some shelves up to "musical chairs" the stuff in the area that is to be insulated and sheeted next

I mitered the corners so no visible end grain, and will fill all countersunk screw holes

Oh, and I scored a bunch of oak cabinets off Craigslist from a house somebody was remodeling. Will need a good cleaning and some RnR, but will work great in the shop

Sent from my iPhone using Tapatalk

JR · « **Reply #29 on:** April 26, 2017, 06:53:44 PM »

I like the sheeting and the mitered ends. My shelves just screw into the studs where ever the are.

I will admit My end supports are like that, but they are on the end corner and I set the center support flush. I may steal the ply walls (then rock) for my new cabinets as they are all lengths.

Dawg25385 · « **Reply #30 on:** April 26, 2017, 10:07:51 PM »

I lagged into studs too with 4" TimberLok's. I want to do something else with the vertical support, but had to get it up and sturdy to get stuff moved and on to insulating

Sent from my iPhone using Tapatalk

JR · « **Reply #31 on:** April 26, 2017, 10:12:06 PM »

Quote from: Dawg25385 on April 26, 2017, 10:07:51 PM

I lagged into studs too with 4" TimberLok's. I want to do something else with the vertical support, but had to get it up and sturdy to get stuff moved and on to insulating

Sent from my iPhone using Tapatalk

I like the timberlocks, but don't use em shelves to much. You should see the straps holding my overhead shelves!

rpar86 · « **Reply #32 on:** April 26, 2017, 10:43:14 PM »

Maybe get some 1" square tube? Might be more aesthetically pleasing and smaller dimensionally to look around when looking for that pesky tool you know you put on that shelf ;)

Dawg25385 · « **Reply #33 on:** April 26, 2017, 10:47:06 PM »

Heck I could prob get away with a 2x2, I think I even have one laying around...

Sent from my iPhone using Tapatalk

JR · « **Reply #34 on:** April 26, 2017, 11:29:53 PM »

some of mine;

Bear9350 · « **Reply #35 on:** April 27, 2017, 08:07:57 AM »

You could probably cut a 2x2 to length to fit inside of the shelf at the corner. Start at the top so you can drive a screw up from the bottom of the bottom shelf to secure the bottom of the leg. Maybe make the bottom leg a little beefier as you won't be able to attach that one to the floor.

Dawg25385 · « **Reply #36 on:** April 27, 2017, 10:53:50 AM »

Quote from: Bear9350 on April 27, 2017, 08:07:57 AM

You could probably cut a 2x2 to length to fit inside of the shelf at the corner. Start at the top so you can drive a screw up from the bottom of the bottom shelf to secure the bottom of the leg. Maybe make the bottom leg a little beefier as you won't be able to attach that one to the floor.

Pretty much exactly what I was thinking

Sent from my iPhone using Tapatalk

Dawg25385 · « **Reply #37 on:** April 30, 2017, 05:41:27 PM »

Almost done sheeting, thanks to my dad who helped me all day yesterday. He was my cut man. 18 junction boxes and a electrical panel to cut out. It's not screwed off yet, but will do that and the rest of the small pieces over the next couple days

Cabinets go up after that, and then workbenches.

Sent from my iPhone using Tapatalk

Bigdave_185 · « **Reply #38 on:** April 30, 2017, 06:23:58 PM »

Are you going to apply a coating of any type to the wood or just leaving it?

Sent from my iPhone using Tapatalk

JR · « **Reply #39 on:** April 30, 2017, 07:50:06 PM »

Dawg25385 · « **Reply #40 on:** April 30, 2017, 08:03:21 PM »

Quote from: Bigdave_185 on April 30, 2017, 06:23:58 PM

Are you going to apply a coating of any type to the wood or just leaving it?

Sent from my iPhone using Tapatalk

At this point going to just leave it. Would need to sand off the ink and what not since I didn't pony up for AC, and don't really have the time or patience for that right now lol

Sent from my iPhone using Tapatalk

Sammconn · « **Reply #41 on:** April 30, 2017, 10:53:38 PM »

Not sure if ceiling paint would cover it or not.

It's cheap like dirt, get a sprayer and be done.
You'll regret not doing it while it's easy.
White makes it sooooo bright.

Just suggesting it before it's real full.

JR · « **Reply #42 on:** April 30, 2017, 11:00:15 PM »

Just get the primer/paint combo stuff.

With insulation AC would be nice. I have an 8k unit downstairs and a 12k upstairs.

Dawg25385 · « **Reply #43 on:** April 30, 2017, 11:17:42 PM »

If I did anything it'd be a poly clearcoat. I wanted the wood look :)

Sent from my iPhone using Tapatalk

Bigdave_185 · « **Reply #44 on:** May 01, 2017, 06:21:07 AM »

I would stick with the wood look as well. Shows less dinge and damage. You could spray it with fence sealant to add a little reflectivity for light and keep the wood still protected, where it's inside it's more than likely a single application needed

Sent from my iPhone using Tapatalk