VEHICLES, CAMPERS, and BOATS > Powerplant, Driveline, and Braking
DIFFERENTIAL TECH TIPS
EL TATE:
Figured I'm making these darn things, might as well post 'em!
20. HOW TO MEASURE AND CUT AN AXLE SHAFT (Toyota application, but any "cut to fit shaft" applies).
https://www.youtube.com/watch?v=7KErFkvHGA8
19. NOISE FROM AN AUTOMATIC LOCKER, IS THIS NORMAL?
https://www.youtube.com/watch?v=Tv4Tba7gUC4
18. YUKON DURAGRIP POSITRACTION INSTALLATION WALKTHROUGH
https://www.youtube.com/watch?v=Ubf2qWYGotc
17. HOW TO IDENTIFY A GM 14 BOLT DIFFERENTIAL
https://www.youtube.com/watch?v=y3sXMW1CMVs
16. GEAR TOOTH PARTTERNS EXPLAINED
https://www.youtube.com/watch?v=C-srB9pUEE4
15. DECODING GM RPO CODES FOR YOUR DIFFERENTIAL
https://www.youtube.com/watch?v=dlSCxS7AB40
14. HOW TO PROPERLY GRIND A THICK RING GEAR TO CLEARANCE FOR THE CROSS PIN SHAFT
https://www.youtube.com/watch?v=dAyaY0R4PNg
13. HOW TO IDENTIFY FORD DIFFERENTIAL HOUSING TAGS
https://www.youtube.com/watch?v=90o5QtER-FI
12. YUKON SPIN FREE KIT INSTALLATION WALK THROUGH
https://www.youtube.com/watch?v=VM8OOreOytM
11. INSTALLING A GM 8.2 GEAR INTO A BUICK/OLDSMOBILE/PONTIAC HOUSING
https://www.youtube.com/watch?v=QvGsrxQNass
10. HOW TO IDENTIFY AND REDUCE POSITRACTION CHATTER
https://www.youtube.com/watch?v=JY2L-or4CAc
9. HOW TO STACK CLUTCHES IN A CLUTCH STYLE POSITRACTION
https://www.youtube.com/watch?v=z4TOL1X_aD8
8. HOW TO IDENTIFY DIFFERENTIAL GEAR NOISE, DECELERATION
https://www.youtube.com/watch?v=1OLfNz2nuDU
7. HOW TO BREAK IN A NEW GEAR SET
https://www.youtube.com/watch?v=Imoujpk4neg
6. HOW TO IDENTIFY GEAR RATIO
https://www.youtube.com/watch?v=ORdTuHnK7nA
5. HOW TO PROPERLY MEASURE A SEMIFLOAT AXLE
https://www.youtube.com/watch?v=BgO8LEsNrUY
4. HOW TO IDENTIFY 2 CUT VS. 5 CUT GEARS
https://www.youtube.com/watch?v=6lGIvOXVfcY
3. DRIVELINE MOVEMENT WITH AN AFTERMARKET LOCKER
https://www.youtube.com/watch?v=9na2biUPbZw
2. HOW TO MEASURE CARRIER DECK HEIGHT FOR GEAR RATIO CHANGE
https://www.youtube.com/watch?v=Ad1RoIksCg8
1. THE RIGHT GEAR OIL FOR A CLUTCH STYLE LIMITED SLIP DIFFERENTIAL
https://www.youtube.com/watch?v=_eqb6GfMy0o
Future videos will be posted here, where you can subscribe, https://www.youtube.com/user/YukonGear/videos every Tuesday until we run out of stuff to talk about.
TexasRedNeck:
Why do I get the feeling my head is about to hurt.....
TexasRedNeck:
You look a lot younger than I expected Tate!
I followed most of them but the 2 cut vs 5 cut. Not sure I understood the heel/toe comments and why are there different types? Pros/cons? What is meant by the 2 cut or 5 cut?
KensAuto:
One has 2 cuts, and the other one has 5. You. Are. Welcome.
fyi.
I will delete my dot posts when I'm done messing with Neck.....which may be a while.
TexasRedNeck:
thanks
Navigation
[0] Message Index
[#] Next page
Go to full version