Hello Guest

Author Topic: 2002 Suburban 2500 build thread, Part 2  (Read 57856 times)

0 Members and 4 Guests are viewing this topic.

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
2002 Suburban 2500 build thread, Part 2
« on: January 21, 2019, 08:02:45 PM »
Hopefully I can stay ahead of the non related postings and offer some continuity to what I am building. In part 1, although I was building a LS engine, we were taking pages to chat about Cummins powered Nissans with AAM axles.

Ya, I know, I don't see the correlation either...

So I left the park over there a couple pages from the end of the mindless chatter, where I was getting ever deeper into this Suburban project. Hoping it does not turn into an "Oil-Change" and returns to being driveable, I press ever onward

With the engine secured to the HD stand I use for Cummins engines, I broke it down to just the short block
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #1 on: January 21, 2019, 08:04:37 PM »
I actually started off pressure washing it all again and then spraying some purple degreaser on some heavily gunked up steering and chassis parts. After one pressure washing I was getting down to dull aluminum
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #2 on: January 21, 2019, 08:05:49 PM »
Most things look like this AC compressor mount and will require scrubbing and paint to renew them
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #3 on: January 21, 2019, 08:07:05 PM »
Then I pulled off the motor mounts, and the oil cooler lines. Yes, the gasket had been leaking!
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #4 on: January 21, 2019, 08:08:25 PM »
Then the oil pan was removed to complete the teardown
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #5 on: January 21, 2019, 08:10:46 PM »
This oil pan is one rough, crude casting. That junk in the bottom of the sump is all casting flash, a part of the pan original casting! Other than that I found nothing and went about the business of cleaning the inside of the block up. I used a brake cleaner soaked rag and rubbed everything clean, then cleaned the gasket surfaces and cleaned it all again.
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #6 on: January 21, 2019, 08:11:26 PM »
Looking a lot cleaner:
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #7 on: January 21, 2019, 08:13:13 PM »
After cleaning as much as I could I taped it all up and applied several coats of paint

Tomorrow should start the reassembly in ernest if everything goes OK and no one needs to go to the hospital!
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #8 on: January 21, 2019, 08:14:49 PM »
Still undecided about the torque converter. The stocker was getting the job done, but the temptation to bolt something in of greater capacity and a few hundred RPM more stall is pulling at me.
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Bigdave_185

  • Raising Boys into Real Men!
  • Registered
  • **
  • Posts: 7686
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #9 on: January 21, 2019, 08:50:53 PM »
Kobota orange!!! And did I see mention of Cummins?  I see that Nissan is putting them in Vans now! 

Jk.  Glad the motor came out easy and you were able to get the cam out with no fuss.  Plus now you can switch to a larger oil pan right?


Sent from my iPhone using Tapatalk

Offline stlaser

  • Moderator
  • ***
  • Posts: 10205
  • Official PIA
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #10 on: January 21, 2019, 09:23:29 PM »
Hey Don, for someone who can DOT someone else’s threads up in a New York minute you whine more than a liberal at a trump rally.... :tongue:
Living in the remote north hoping Ken doesn’t bring H up here any time soon…..

Offline KensAuto

  • Moderator
  • ***
  • Posts: 7684
  • My abuser is named Nate
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #11 on: January 21, 2019, 11:24:24 PM »
I'll wait till part 12 of this oil change before saying anything wise azz. ;)
Underpaid and misunderstood since 2014

Offline Bigdave_185

  • Raising Boys into Real Men!
  • Registered
  • **
  • Posts: 7686
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #12 on: January 21, 2019, 11:48:45 PM »
Hey Don, for someone who can DOT someone else’s threads up in a New York minute you whine more than a liberal at a trump rally.... :tongue:
Oh shiZ


Sent from my iPhone using Tapatalk

Offline cj7ox

  • Registered
  • **
  • Posts: 1269
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #13 on: January 22, 2019, 07:58:06 AM »
Hey Don, for someone who can DOT someone else’s threads up in a New York minute you whine more than a liberal at a trump rally.... :tongue:
Oh shiZ


Sent from my iPhone using Tapatalk

 :facepalm:

 :popcorn:
~Sean M. Davis

“The citizens of a free state ought to consist of those only who bear arms.” ~Aristotle

Μολων Λαβε

Offline TexasRedNeck

  • punching bag for moderator humor
  • Global Moderator
  • ****
  • Posts: 11314
    • View Profile
2002 Suburban 2500 build thread, Part 2
« Reply #14 on: January 22, 2019, 08:04:26 AM »
Well you got it out and are flirting with an oil change you might as well install a stroker kit


Sent from my iPhone using Tapatalk
« Last Edit: January 22, 2019, 08:16:23 AM by TexasRedNeck »
Kids today don't know how easy they have it. When I was young, I had to walk 9 feet through shag carpet to change the TV channel.

Joshua 6:20-24

Offline swbhobie16

  • Registered
  • **
  • Posts: 1258
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #15 on: January 22, 2019, 08:50:19 AM »
ohh for goodness sake.. leave the man alone. he’s just trying to get a reliable grocery getter. no need to get into TTs and centrifugal blowers on an LS.

ohh wait. did i say that out loud?   :cheesy:

Offline stlaser

  • Moderator
  • ***
  • Posts: 10205
  • Official PIA
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #16 on: January 22, 2019, 08:53:52 AM »
 :popcorn:
Living in the remote north hoping Ken doesn’t bring H up here any time soon…..

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #17 on: January 22, 2019, 09:46:14 AM »
Hey Don, for someone who can DOT someone else’s threads up in a New York minute you whine more than a liberal at a trump rally.... :tongue:
Stop it! ;-))
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #18 on: January 22, 2019, 09:47:22 AM »
Well you got it out and are flirting with an oil change you might as well install a stroker kit


Sent from my iPhone using Tapatalk
I knew someone was going to say that!
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #19 on: January 22, 2019, 09:48:09 AM »
ohh for goodness sake.. leave the man alone. he’s just trying to get a reliable grocery getter. no need to get into TTs and centrifugal blowers on an LS.

ohh wait. did i say that out loud?   :cheesy:
Yea, leave the man alone...!!!

OK, then, back to the Kubota engine it is! ;-))
« Last Edit: January 22, 2019, 09:49:08 AM by Flyin6 »
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline cudakidd53

  • Moderator
  • ***
  • Posts: 3142
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #20 on: January 22, 2019, 01:54:49 PM »
That’s starting to look like a Mopar block all oranged up!
2012 Silverado LTZ - Duramax
Christian since 1975 - Field Trial Brittanys - NRA Lifetime Member

"When you're dead, you don't know you're dead. Hence, dealing with this fact is not difficult. It is only hard for those still living around you.....It's the same when you're stupid."

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #21 on: January 22, 2019, 07:40:06 PM »
That’s starting to look like a Mopar block all oranged up!
Dave sez its Kubota, I thought it was black, so whatever...I'm good
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #22 on: January 22, 2019, 07:51:15 PM »
Starting to zero in on the bumper with Bear (Brian). Hey, that's close to bear Bryant...Roll tide!

Going with three different sized holes in the front bumper, 5" inside, 4" just outside of that, and 3" in the flats on the sides for rock crawling lights

He was playing with ideas for a brush guard, but for now, I'll forgo that and just get a bumper/winch on the front to bolster capability

We still have some work to do on the rear, and we have decided to re-install the factory hitch in lieu of Brian's much heavier, and more capable offering pictured below:
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline KensAuto

  • Moderator
  • ***
  • Posts: 7684
  • My abuser is named Nate
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #23 on: January 22, 2019, 08:06:37 PM »
That Brian guy is sure professional, using fancy computers and what not. ..bet he works on space ships as a hobby...oh wait,  that's the pig sticking guy out west.
Kidding aside, I like the design(s).
Underpaid and misunderstood since 2014

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #24 on: January 22, 2019, 08:22:47 PM »
Well like always, I like using talent from right here, like you, Ken as you will see shortly with tonight's post. Yes, Brian is easy to work with and pays attention to detail. I hope that lots of folks see his work here and order bumpers from him.
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #25 on: January 22, 2019, 08:23:38 PM »
So the paint cured out fine. My Kubota engine is lookin' purdy!
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline BobbyB

  • Global Moderator
  • ****
  • Posts: 3030
  • "You are not LaBeouf"
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #26 on: January 22, 2019, 08:23:53 PM »
order bumpers from him.

I was going to for XJ but it went away before I could. Perhaps with the WK2, since apparently only ARB wants to make a front bumper and no one makes a rear bumper.
« Last Edit: January 22, 2019, 08:25:30 PM by BobbyB »
So, Bobby...being the calculating trained warrior NCO that you are.  Take the appropriate action, Execute!
your standard grunt level CQB is just putting rounds and rounds on scary stuff till it stops scaring you!

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #27 on: January 22, 2019, 08:25:22 PM »
But one thing that wasn't very nice looking is the oil pan. Look at that casting flash. Must have been cast in a russian tank factory!
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #28 on: January 22, 2019, 08:32:01 PM »
Wire brushed, sanded smooth, cleaned and re-cleaned, and painted
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #29 on: January 22, 2019, 08:36:13 PM »
Gave a similar treatment to the other parts and coated the motor mounts with bed liner. Harbor Freight stuff, but sprays like the more expensive stuff
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #30 on: January 22, 2019, 08:38:05 PM »
And oh, by the way, this is the single pesky bolt that caused me to remove the engine from the chassis. Like many of you suggested, it just made too much sense not to!
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #31 on: January 22, 2019, 08:39:00 PM »
Felpro center valley cover gasket kit
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #32 on: January 22, 2019, 08:40:23 PM »
Which included the rubber seals that seal contaminants out of the engine internals while isolating the knock sensors
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #33 on: January 22, 2019, 08:43:41 PM »
That went together easily
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #34 on: January 22, 2019, 08:45:06 PM »
New wiring harness as per Ken's recommendation
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #35 on: January 22, 2019, 08:46:42 PM »
Used some stickems to hold down the harness, then applied a 1/4" tall dam of RTV as per the GM bulletin that Ken also supplied. So, thanks to him, I think the job is done right.
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #36 on: January 22, 2019, 08:49:03 PM »
It's a 6.0L for sure!

Next up the cam/timing cover. Bolts loose for now, snugged after the oil pan install
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #37 on: January 22, 2019, 08:51:27 PM »
Bolting stuff back on...good feeling to reverse the trend line!
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #38 on: January 22, 2019, 09:46:32 PM »
Felpro supplied the oil pan gasket. I applied four small dabs of RTV to the parting lines of the front and back covers where they mate to the oil pan
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #39 on: January 22, 2019, 09:47:26 PM »
Then torqued the oil pan down
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #40 on: January 22, 2019, 09:48:33 PM »
And that is the enchilada for today, get back at it in the morn.
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline TexasRedNeck

  • punching bag for moderator humor
  • Global Moderator
  • ****
  • Posts: 11314
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #41 on: January 22, 2019, 10:17:35 PM »
So I guess that means no stroker kit?


Sent from my iPad using Tapatalk
Kids today don't know how easy they have it. When I was young, I had to walk 9 feet through shag carpet to change the TV channel.

Joshua 6:20-24

Offline cruizng

  • Registered
  • **
  • Posts: 1112
  • Happy to be here.
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #42 on: January 23, 2019, 08:47:19 AM »
And oh, by the way, this is the single pesky bolt that caused me to remove the engine from the chassis. Like many of you suggested, it just made too much sense not to!

Don,

Could you replace the pesky bolt for a 2 or 3" stud or cobblefabricate a longer bolt to make it easier on the next guy that need to reach it and still have clearance?  :popcorn:

Mike
Sold the DMax in MN and am currently vehicle less.

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #43 on: January 23, 2019, 09:27:52 AM »
So I guess that means no stroker kit?


Sent from my iPad using Tapatalk
Not for now my friend
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #44 on: January 23, 2019, 09:33:06 AM »
And oh, by the way, this is the single pesky bolt that caused me to remove the engine from the chassis. Like many of you suggested, it just made too much sense not to!

Don,

Could you replace the pesky bolt for a 2 or 3" stud or cobblefabricate a longer bolt to make it easier on the next guy that need to reach it and still have clearance?  :popcorn:


You could put a stud in there,

But

You still have to either pull the motor, or drop the front diff to get the pan down far enough to get the bolt started, and all the while you can't see what you are doing

Keep in mind, this is the MAIN AND ONLY oil supply for the engine. Get this one operation wrong and you are back to A. Pull the engine.

Secondly, remember Ken's dire warning: Don, there is no other way to say this, your oil pan is now going to leak

I'm only a pilut, and not a very bright one, but that was as clear to me as when my wife told me "If you join the Army again and go off to war, I'll divorce you! Simple easy to sort through messages are the most effective for me.

So, in the end it was the factory bolt with a dab of lock-tite blue
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline cruizng

  • Registered
  • **
  • Posts: 1112
  • Happy to be here.
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #45 on: January 23, 2019, 09:43:58 AM »
Carry on then... :) Just trying to get my DOT quota in for the day:popcorn:


Moderator Comment: Placin' you on notice, cause, I noticed what ya just said...Be careful... ;-)
« Last Edit: January 23, 2019, 09:49:18 AM by Flyin6 »
Mike
Sold the DMax in MN and am currently vehicle less.

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #46 on: January 23, 2019, 08:04:48 PM »
Wheels showed up from 4-wheel parts

Well spent $412!!!!!!!!!!
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #47 on: January 23, 2019, 08:05:40 PM »
Started today installing the new Fumota oil drain valve
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #48 on: January 23, 2019, 08:06:20 PM »
Starting with an extension since my oil pan has the drain plug recessed
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

Offline Flyin6

  • Head cook and bottle washer
  • Administrator
  • *****
  • Posts: 34008
    • View Profile
Re: 2002 Suburban 2500 build thread, Part 2
« Reply #49 on: January 23, 2019, 08:07:16 PM »
This one has a 90 degree petcock which can be oriented in any direction
Site owner    Isaiah 6:8, Psalm 91 
NSDQ      Author of the books: Distant Thunder and Thoren

 

SimplePortal 2.3.6 © 2008-2014, SimplePortal