This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - JR
Pages: 1 ... 123 124 [125] 126 127 ... 270
6201
« on: February 06, 2019, 08:25:01 PM »
Heck, I want to see pics of the B29!!
6202
« on: February 06, 2019, 10:41:04 AM »
Since you had it out and pulled the converter. Looked like it wasn't leaking should be OK.
6203
« on: February 05, 2019, 11:59:32 PM »
Guess I shouldn't ask, did you replace the seals?
Dana 80, seen those on some 80s cummins.
6204
« on: February 05, 2019, 11:55:25 PM »
^^^^  ^^^^
6205
« on: February 05, 2019, 11:54:35 PM »
I don't see an issue either, but seeing the rust in there made me think a little.
I have seen rebuilds where they rub anti-seize on the surface.
Must say it looks good though.
6206
« on: February 05, 2019, 07:05:53 PM »
Weird, leaving a drain line not attached, good thing you found it.
6207
« on: February 05, 2019, 12:20:01 AM »
I liked that one too. Heard some bozo on the radio today complain about the wasted food,,,,,,,,,
6208
« on: February 05, 2019, 12:14:20 AM »
So they are protesting the same thing they are doing?
Half looked dazed and so brave they have to wear a mask?
6209
« on: February 05, 2019, 12:06:08 AM »
Hey, K has a cute but.
6210
« on: February 04, 2019, 11:35:10 PM »
You'll be fine. Just sip a little more.
6211
« on: February 04, 2019, 06:55:28 PM »
Across the street is nice, maybe the other as a backup for a rainy day,,,,,,,,,,,,
With all the 6L80Es being run out there, you would figure a cheaper controller would be available for it.
6212
« on: February 04, 2019, 04:42:30 PM »
The 1991 had a stand alone PCM for the trans, only year. Mine works great in the 85 burb, not sure of the PCM though. What PCM you looking at?
6213
« on: February 04, 2019, 04:37:20 PM »
Not sure about a snorkel, does that green thing run??
Looking at pulling air from the inlet area below the window. Could always add to that.
The KnN 38-2006S looks interesting, but need the R version in that size.
6214
« on: February 04, 2019, 03:31:48 PM »
I don't want to pull the air from the fender, but guess I could block that side off and run a tube to where I want.
6215
« on: February 04, 2019, 12:55:47 PM »
Those are close, but I need a side outlet, center in. I think the first one is for a lawn tractor.
I did some searching too, need something I can lay flat, change filter from the top.
6216
« on: February 04, 2019, 12:29:55 PM »
You would prefer a 700r to a T400 on something with that much torque?
Thinking 4L80
Good choice
6217
« on: February 04, 2019, 11:11:55 AM »
Need them on the front, rear is OK but they don't get same road debris or abuse as the front does.
6218
« on: February 04, 2019, 01:58:52 AM »
I need ideas too on the air cleaner. I posted a couple ideas in post 42. The 90s GM filter will work, but I want a round canister if I can find one that doesn't break the bank.
6219
« on: February 04, 2019, 01:36:38 AM »
Going to get the front end weighed so I can order my springs and get this thing going. Yep, going to stay with springs and Deavers. Found a vid using the sliders, think they will be just fine and keep me lower. https://youtu.be/yoYrt9dO1ow
6220
« on: February 04, 2019, 01:32:53 AM »
Got covers for the battery terminals. It also starts easy all the time now so the effort was really worth it.
Got my 2nd set of spacers in, billet so they are stronger than most wheels. 2.5in with 14mm studs onto the 9/16 stock studs giving me a 4.5bs. This allows running the H1 wheels on the stock axles and can put on stock wheels if need be anytime. Thinking of running a steel outer shim so the H1 wheel bolts up to it flat and not into the machined surface with BIG holes.
If the rain quits this week I am going to put the front lift springs on to level this thing out. It has a 4 inch block in back and I can replace that with a 2in I have or just throw the new springs out back. I need the lift for the 37 tires.
6221
« on: February 03, 2019, 11:13:52 PM »
Wheels look good, just a little small for my taste.
Garage door opener on the fitz. Had a power outage, then a surge and it works when it wants to now. LM 8500. Have a new control panel on order. They are sending out new ones like warranty/over 5 years old!
6222
« on: February 03, 2019, 08:17:47 PM »
Those 500s are monsters and lightweight.
Just saw the donner in the superbowl halftime!!
6223
« on: February 03, 2019, 08:10:12 PM »
Like it all.
6224
« on: February 03, 2019, 04:30:59 PM »
Still sticking with leafs
6225
« on: February 03, 2019, 12:12:57 PM »
Funny, the guy I got my axle from was touting that guy big time. Even wanted me to go up to the shop but I didn't have time.
He had nothing but good to say about the guy, but was up front he was pricey.
6226
« on: February 02, 2019, 11:51:36 PM »
Seen those clips on TV. Evens em out, right?
6227
« on: February 02, 2019, 11:47:51 PM »
I have to get another set of high steer stuff for the DMax SAS, and rebuild the axle, get springs,,,,,,,,,,,,,,
Hey, I have the axle and the dmax!
6228
« on: February 02, 2019, 09:12:23 PM »
Fixed the "my bushings"
Will be my first front build, done several rears.
6229
« on: February 02, 2019, 08:43:53 PM »
Good looking rims. I can never get the offset right, plus = Neg???
Ordered spacers for the Burb to run the H1 wheels. Have two 2.5" already so that gives me a 4.5 BS.
6230
« on: February 02, 2019, 08:37:23 PM »
On the staircase, is there a brace under the lower step after the floor?
6231
« on: February 02, 2019, 08:32:05 PM »
Great work. Hope my bushings fit OK. I can machine though if required.
6232
« on: February 02, 2019, 03:09:34 PM »
Yep, needs a little lift.
Nice work!
6233
« on: February 02, 2019, 12:44:22 PM »
Use you foot if that close,,,,,,,,,,,,,,,,
6234
« on: February 01, 2019, 10:10:29 PM »
Engine?
6235
« on: February 01, 2019, 10:01:02 PM »
Both of those look good TRN.
Keep thinking about putting a ring here, new place for sure!
6236
« on: February 01, 2019, 07:31:42 PM »
Have you thought about a recoil pad?
6237
« on: February 01, 2019, 03:42:13 PM »
I doubt Roberts would follow any preset based on recent decisions.
6238
« on: February 01, 2019, 03:38:49 PM »
Hey, you know my wife! 
6239
« on: January 31, 2019, 11:19:08 PM »
I like that. Out of sight but right there!
6240
« on: January 31, 2019, 08:20:57 PM »
Just an FYI really. To bad his kid was right there.
6241
« on: January 31, 2019, 03:16:33 PM »
6242
« on: January 31, 2019, 02:38:07 PM »
6243
« on: January 31, 2019, 01:29:47 PM »
Nothing new about that. Funny how we didn't even hear about it hear, or it was so short lived they buried it quick!
6245
« on: January 31, 2019, 10:13:14 AM »
Because cattle don't eat the equipment.
6246
« on: January 31, 2019, 10:09:28 AM »
Probably dads warm shop,,,,,,,,,,,
6247
« on: January 30, 2019, 10:26:24 PM »
Ever see the movie "Knowing",,,,,,,,,,
6248
« on: January 30, 2019, 10:24:36 PM »
Margaret Thatcher would have a field day with AOC.
Remember, its the "new math" where close enough is correct.
6249
« on: January 30, 2019, 10:19:30 PM »
Its global warming, cooling, er shifting. But think, in 12 years its all over anyway.
Now, does anyone here really think we can do anything about any of it?
6250
« on: January 30, 2019, 09:55:24 PM »
That looks so easy. Getting it out is the issue.
Pages: 1 ... 123 124 [125] 126 127 ... 270
|
Show Posts
