This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - Flyin6
Pages: 1 ... 410 411 [412] 413 414 ... 671
20551
« on: September 17, 2016, 04:57:14 PM »
This outward spacing pulled the stubby pipe section inside the wall, rendering it useless in my application so, until I visited SLOWES once more, the Chimney project is dead in the water, but easily completed with just a couple replacement pieces
So it was back to wiring. First up was the three gang switch box and the 20 amp compressor circuit
20552
« on: September 17, 2016, 04:54:02 PM »
So, as a solution to the problem, I simply built a base outward from the wall from four sections of 2 X 6, each an inch shorter than the one beneath. I used long t-25 wood screws to fasten the pieces. Afterward it was a solid mass, so I painted it
20553
« on: September 17, 2016, 04:52:22 PM »
Here is a section of chimney pipe which measures 36" long and the very pipe that showed me I was way too close to the eve to make this actually fit properly.
20554
« on: September 17, 2016, 04:50:44 PM »
I thought I was cookin' with bacon grease and the project was just zipping along. But, wait a minute...Look at the distance of that pipe from the wall, and how far out the eve is setting...
Yep, I was about 6" too close to the building
Not knowing that I attached the stove pipe adapter. Notice that these sections sort of "Screw" together maybe an eighth of a turn
20555
« on: September 17, 2016, 04:47:14 PM »
Then I assembled the three piece base, slid the "T" home and slid up the base and screwed it to two studa
20556
« on: September 17, 2016, 04:46:16 PM »
OK, Tool time
Since I'm trimming the cedar trees to become parts of my ever expanding shed/house, I picked up these quality EastWing axes to cut the knobbies down a bit before I continue to process the log.
I didn't have time to use them this time as I was cut a bit short due to inclement weather
I have the short handled 5# maul for splitting kindling, it's very nice
I was going to get mine marred up later today if the rain not started
20557
« on: September 17, 2016, 04:45:17 PM »
The "T" section requires you to add a transition pipe to the inside. I had selected a 12" section which soon proved to be a bit too short.
This "T" section just reeks of quality
20558
« on: September 17, 2016, 04:42:47 PM »
I cut and modified the cement wall board then reattached and slid home the thimble piece
20559
« on: September 17, 2016, 04:41:27 PM »
As you can see, a chamber is created with dead space between the stove pipe and the double steel panel. The outside fixture creates one layer of steel, while the interior wall thimble creates the second.
Its a slick setup
20560
« on: September 17, 2016, 04:39:45 PM »
Then, the outside metal bulkhead part is screwed into place
20561
« on: September 17, 2016, 04:38:39 PM »
First I had to enlarge the hole in the wall I cut out a few days ago
20562
« on: September 17, 2016, 04:37:44 PM »
This box has the wall mount for the "T" pipe and will support the weight of the upright Chimney sections, which will rise 9 feet above the wall outlet
20563
« on: September 17, 2016, 04:36:21 PM »
The tool rack seems to expand a bit more each time I visit.
My goal is to improve the site each time I go down there, to have more capability, and be closer to actually be able to go it alone and off grid there
20564
« on: September 17, 2016, 04:34:36 PM »
The quality is superb. The stuff is made in Canada, which I have found to be as good or better than US made stuff
20565
« on: September 17, 2016, 04:33:32 PM »
Because of Sam's recommendation and since his neighbor is Santa Claus, I hunted down the quality Chimney parts he recommended
20566
« on: September 17, 2016, 04:31:47 PM »
OK, Tool time
Since I'm trimming the cedar trees to become parts of my ever expanding shed/house, I picked up these quality EastWing axes to cut the knobbies down a bit before I continue to process the log.
I didn't have time to use them this time as I was cut a bit short due to inclement weather
20567
« on: September 17, 2016, 03:21:58 PM »
Just getting back from another couple days down at the hide.
Had both:
1. A UNE (Unnatural, Natural event)
and
2. A UTE (Unintentional Turkey Encounter)
The UNE is a sled dog, not naturally occuring in these parts coming in very close proximity to a turkey of about the same size. That just ain't right, thus it becomes unnatural, although dogs encounter other edible creatures and that is very natural
It was a UTE since the dog was sleepin' whilst a big hen strolls into my back yard at the farm. The dog, spooked by my throwing something at it decides to relocate. The dog unwittingly walks right up on this monster (Godzilla like) turkey who was brazen enough to be walkin around in my yard during daylight hours while I am knockin' and bangin' on things and blessing my latest finger smashin' event (FSE)
I actually heard it before I saw it. I hear this unhold gobble/scream and my lightening fast reflexes has me by a window maybe 30 feet away from the sled dog almost nose to nose with this thing which I know she is evaluating as a meal. The bird just exploded in a mad whooshing of wings which had a frightening effect on the sled dog and the bird made good it's escape.
Would you know it, this morning that darned bird came back!
Now that's pure crap!
I have a sled dog, perhaps 100lbs of very near wolf like mannerisms and the little german soldier who runs away at first indication of trouble. Neither of these stalwart warriors seem to have any effect on this Turkey who seems to be challenging them somewhat
What next? A lying, cheatin' communist president?
20568
« on: September 16, 2016, 09:29:32 PM »
UOA???
20569
« on: September 16, 2016, 09:23:06 PM »
My neighbor across the street has that exact same quad!
Just go at it slowly and go over every part
Just fix what needs fixing
DO NOT do a comprehensive oil change!!!!!
20570
« on: September 16, 2016, 09:16:36 PM »
It used to be about my truck
But who cares...
I'm learning same as all you boneheads
So carry on,
20571
« on: September 16, 2016, 09:09:05 PM »
Got a DOT goin on here
Think I'll just sit back and watch what happens
20572
« on: September 16, 2016, 08:23:56 PM »
I appreciate all the help!
So today I went to the hide again and sort of installed the new Canadian chimney parts...Right up to the point where I was sticking on the first long section of outside riser Someone installed a roof overhang in the way!
I needed to build the mount 6" past the wall which made my inside transition pipe about 8" too short
I'm looking at another trip to lowes to change out the 12" pipe. After that and cutting the stove pipe to proper length and I'm going to have one slick setup
Meanwhile I'm back to wiring things and hitting my fingers!
20573
« on: September 16, 2016, 09:19:36 AM »
Packing up and heading to Detroit for my Daughters wedding........sure are proud of their Hotel rooms downtown; can get robbed many ways in that town!
Looking forward to some down time and a trouble-free celebration!
Practice in-laws and practice-wife will provide some comic relief I'm sure.... :o. Toss my Dad in the mix and it could be "The Clampets Go To Detroit" ;D
Get a vid of the quirky moments!
20574
« on: September 16, 2016, 08:46:28 AM »
Nice job!
I won't compare the staircase I built in the spring...
Yours is better!
20575
« on: September 16, 2016, 08:44:40 AM »
Now, we need female droids to walk in wearing a burkas and a suicide vest and blow a few dozen up and see just how long it takes for the burka to fall out of "style"......... ;)
I like it!
20576
« on: September 16, 2016, 08:41:30 AM »
Do you think the 4.56 gears (coupled with Isiah 6:8 of course) may be the reason for your good mileage? So far as I can tell, getting these pigs moving takes more fuel than maintaining momentum. Years ago, when I lifted and put 35s on my 89 K1500 I thought I would get better mileage because the motor would run at lower rpm while cruising around. Boy was I wrong.
Sent from my iPhone using Tapatalk
Could be... But I'm leaning toward righteous living as the root cause I've been trying to do that with some limited success Ain't God good!
20577
« on: September 16, 2016, 08:34:27 AM »
Psalm 119
1 Joyful are people of integrity, who follow the instructions of the Lord. 2 Joyful are those who obey his laws and search for him with all their hearts. 3 They do not compromise with evil, and they walk only in his paths. 4 You have charged us to keep your commandments carefully. 5 Oh, that my actions would consistently reflect your decrees! 6 Then I will not be ashamed when I compare my life with your commands. 7 As I learn your righteous regulations, I will thank you by living as I should! 8 I will obey your decrees. Please don’t give up on me! 9 How can a young person stay pure? By obeying your word. 10 I have tried hard to find you— don’t let me wander from your commands. 11 I have hidden your word in my heart, that I might not sin against you. 12 I praise you, O Lord; teach me your decrees. 13 I have recited aloud all the regulations you have given us. 14 I have rejoiced in your laws as much as in riches. 15 I will study your commandments and reflect on your ways. 16 I will delight in your decrees and not forget your word.
20578
« on: September 16, 2016, 08:15:42 AM »
OK, after Sam turned me on to that Canadian stove pipe company, I got to reading a bit more.
I decided to just redo the whole thing. I discovered that SLOWES carries that exact company's products so $703 later, I bought everything new and loaded it into the back of C-Max.
Good lead there, Samuel! Very well build stuff in those boxes, and now I'll have a bomb proof system that will safely heat that shed for the rest of ma' daze!
20579
« on: September 16, 2016, 08:12:52 AM »
Is that table saw going to stay there? If so, thought about turning the stove so you have a bit more room to move before you apply clothes or skin to hot metal heater.. Cause it will happen.
Gotcha!
20580
« on: September 16, 2016, 08:12:35 AM »
First thing to hit the top of that stove will be "Chinook Cooked Shrimp" I predict......what was on that in addition to Old Bay?
Old Bay, small red potatoes and corn cobs cut into three pieces...That's it! I'll make ya a better batch next time you show up Mike...Those were a bit over done.
20581
« on: September 16, 2016, 08:10:36 AM »
No, Nate, not me
Sorry for the misunderstanding, but I just copied a letter from one of the attendees.
20582
« on: September 16, 2016, 08:09:05 AM »
I have always run with the 150HP deleted tune from H&S. Not just deleted, but no EGR and manifolds and up-pipes as well as a good down pipe and exhaust.
Think about it, I am getting that, well, usually I get high 17's to mid 18's on the same drive, but lately it is getting 19's...But I am doing all that with 4.56 gears and the 35's. That would be roughly approximate to a regular truck driving around at 70MPH.
Something is definitely right with my combo!
Personally I think it has a lot to do with the Isiah 6:8 scripture which I have proudly displayed in the back, I get a natural resistance from things that hold one back which obviously increases the distance you can go!
20583
« on: September 15, 2016, 11:17:57 PM »
Here's an ISIS story that will make your day! This is one time you will actually appreciate how useful the burka can be! British special forces troops donned the full-length Islamic dress to sneak undetected through the ISIS' de facto capital Raqqa and take down their terrorist commander, news reports. The eight-man SAS squad also eliminated several jihadi fighters after lifting up their burkas and opening fire on the stunned militants, who had no time to hide from the hail of bullets. The men posed as ISIS chiefs wives by covering themselves from head-to-toe in the traditional black burkas and managed to make their way to the group's headquarters. Underneath the burkas the troopers had grenades, machine guns and enough ammo to rain hell upon the terrorist scumbags. Priceless! After making their way through the town they located the house of a senior terrorist chief and relayed the location and coordinates to a US Air Force AWAC mission control aircraft circling thousands of feet above. https://media.licdn.com/mpr/mpr/shrinknp_800_800/AAEAAQAAAAAAAAf3AAAAJDk0Nzc3NzEzLWY3M2EtNGVjMy05MDM4LWE5NDZkNzJiZGNlMg.jpg The American spy plane then passed the information onto a US Reaper drone, which seconds later fired a Hellfire missile into the building, vaporizing the ISIS commander and several of his henchmen, The Express reported. When jihadi militants heard the explosion they rushed onto the streets and discovered the burka-clad troopers, who took down several Jihads during a fierce gun battle as they fought their way to safety. "The SAS team were moving back to their vehicles after the missile had struck when the town went into lockdown," a source revealed. "Gunmen were on the streets stopping everyone, lining people up against the walls and threatening to kill anyone who had helped the 'spies'." "Just as the British soldiers were getting back into a minivan several gunmen ordered them to stop," the source said. "The troopers ignored the warnings and were about to drive off when the Jihads opened fire." "The SAS jumped out of the vehicle, lifted up their burkas and opened fire. It must have been a massive shock to the gunmen," recalled the source. "One was killed instantly and two others ran off. The firefight gave the SAS just enough time to break contact with the ISIS gunmen and escape." A good friend, on the ground reported that shortly after the daring raid, rumors started swirling around town that the "infidels" had sent women to do their fighting rather than men, the source said. However, as we know now, it was actually eight brave soldiers with far better training and much better equipment, and the result was that they struck a "severe blow" to ISIS/Daesh in the area. It definitely takes a brave man to walk straight into the pits of hell like these soldiers did, especially knowing the consequences if they were caught. But it's awesome they used Islam's own rituals to infiltrate the group, then wreak havoc.
20584
« on: September 15, 2016, 02:56:34 PM »
From strictly a fuel perspective, it's hard to make an argument against Propane. Last forever, multiple uses, you can store large amounts which you'd buy during the warm months...
Diesel would be a decent second choice assuming you had a good storage system and you added to it every once in awhile to keep the mixture a bit fresher.
Gas, well, I think it's a no-go for survival purposes because the gas goes away too fast, and with today's crappy alcohol/gas blends the stuff doesn't last very long at all...Just ask the mikuni carb on my DR-650!
Size wise, I concur with the above. Transfer panel with just the essentials makes good sense. Then sizing a unit from as low as your 8K, upward to maybe a 16KW unit if your needs are higher (Electric heater, essential life support equipment, or things like that)
20585
« on: September 15, 2016, 02:39:19 PM »
I sort of noticed that when I tried to shove some 12 gage wire into the hole while experimenting...It wouldn't fit!
Hilly-Billy proof! Whatcha know!
I'm kinda surprised that you didn't just drill the holes out, or shave the wires down to make them fit. ;)
Didn't have the right sized drill bit! ;-))
20586
« on: September 15, 2016, 02:34:33 PM »
A true 20-amp plug has the sideways T-shaped neutral pin - accepts standard 15 amp or the 20amp plug like what is on my neighbor's 120V welder.
Thanks I'm on it!
20587
« on: September 15, 2016, 02:33:13 PM »
Oh, and notable wave and thumbs to our frozen Canadian friend, Sam, for straightening me out before I generated a building fire and Car-Rep-3 incident!
20588
« on: September 15, 2016, 01:36:06 PM »
Don, a note on using the backwire outlets... the outlets you have pictured are for 15a circuits, (we'll ignore that for now) so the backwire on those will only accept 14ga wire. Wrapping the wire around the screws as you did is a mo-betterer practice anyway, regardless of wire size. I wired my entire garage this way with 15amp plugs I took out of the house (hate the almond color, replaced them all with white).
*i'm not an electrician, so all comments should be taken with a grain of salt.
Carry on good sir!
I sort of noticed that when I tried to shove some 12 gage wire into the hole while experimenting...It wouldn't fit! Hilly-Billy proof! Whatcha know! I just realized, though that the compressor outlet has a 15 amp outlet on a dedicated 20 amp circuit...Gonna have to change that out. Well, I'm off to SLOWES to spend some more of my dwindling "Builder-Bucks!"
20589
« on: September 15, 2016, 01:32:51 PM »
Don, in here you will find some installation details. As well you may be able to source the transition pieces you need.
http://www.selkirkcorp.com/SuperVent/Product.aspx?id=100
I don't know what brand you have, this one is very common, but may not be what you have.
I think you need a metal wall 'installation' piece, and I'm not sure about the wooden cradle outside. You may want to look at their options as well.
More info, less DOT this time.
All looks good in any case.
^^^^^ That's a good post^^^^^ Don, in here you will find some installation details. As well you may be able to source the transition pieces you need.
http://www.selkirkcorp.com/SuperVent/Product.aspx?id=100
I don't know what brand you have, this one is very common, but may not be what you have.
I think you need a metal wall 'installation' piece, and I'm not sure about the wooden cradle outside. You may want to look at their options as well.
More info, less DOT this time.
All looks good in any case.
Holy crap Sam! I think I need to re-do that chimney pipe installation! Just went to that link and THAT is the stuff I need Gonna be spendy though... Usin' my SLOWES discount of 10% I'll take it from ridiculous to just crazy expensive...
20590
« on: September 15, 2016, 12:22:33 PM »
And you my fine Wilburin' friend are the "1-DOT" (First D.O.T er to screw with my thread)
Well sumbuddy had to step in while the west coasters were sleeping late... ;D
Proper Spellin' noted! ^^^ One point awarded
20591
« on: September 15, 2016, 12:18:26 PM »
Don, in here you will find some installation details. As well you may be able to source the transition pieces you need.
http://www.selkirkcorp.com/SuperVent/Product.aspx?id=100
I don't know what brand you have, this one is very common, but may not be what you have.
I think you need a metal wall 'installation' piece, and I'm not sure about the wooden cradle outside. You may want to look at their options as well.
More info, less DOT this time.
All looks good in any case.
^^^^^ That's a good post^^^^^
20592
« on: September 15, 2016, 12:06:33 PM »
Oh, I remember...
That's the spot where I'm going to cut a sizable hole to heat the upstairs, and for small children to more easily be able to climb down through onto the hot stove...
20593
« on: September 15, 2016, 12:04:33 PM »
Here I am deciding which combustible to store next to the stove, and another pic of me pointing at something...
20594
« on: September 15, 2016, 12:03:04 PM »
Tractor-2 overheated several times and blew a hydraulic hose off the steering cylinder and had a flat tire...But I consider that minor any more. I actually had a spare hose down there, so all of that only mounted to a few Car-Rep 1 events!
Oh, and the bush hog pulled off again when one of the lower three point arms fell off (Again)
20595
« on: September 15, 2016, 11:59:56 AM »
Well, it was on to more pasture weed killin' fun
I try to spend part of the day building in the living area, and part of it improving the land. Some day, I'll have one or the other, more or less, under control.
20597
« on: September 15, 2016, 11:55:24 AM »
I once observed that a man of peace could be identified when a butterfly lands on him to rest.
While I was bush hogging and destroying it's habitat, a butterfly landed on my shoulder and rode around awhile.
Similarly, I no sooner mounted the shelf, like 5 seconds, when this guy showed up for a rest:
20598
« on: September 15, 2016, 11:52:47 AM »
Next I finished off the wall with cement board and added a shelf.
The shelf was made from old and very hard oak barn wood I salvaged from the wood pile my wife thinks is a barn
20599
« on: September 15, 2016, 11:50:56 AM »
Surprised...No one has interrupted me yet...
I think we have a NDAE (No DOT Activity Event!)
Which is rare indeed!
Like palliated woodpeckers...The big red headed protected things which taste like chicken! Yumm!
20600
« on: September 15, 2016, 11:48:28 AM »
Another think I have yet to work out is that the stove outlet is sized for 8" pipe
But if you look, the double chimney pipe is sized for 6" pipe!
I checked and the original pipe which I found in the Sarge created debris pile was indeed 6", however no 8" to 6" transition could be found!
Gotta figure that one out
Pages: 1 ... 410 411 [412] 413 414 ... 671
|