VEHICLES, CAMPERS, and BOATS > Powerplant, Driveline, and Braking

DIFFERENTIAL TECH TIPS

(1/9) > >>

EL TATE:
Figured I'm making these darn things, might as well post 'em!
20. HOW TO MEASURE AND CUT AN AXLE SHAFT (Toyota application, but any "cut to fit shaft" applies).
https://www.youtube.com/watch?v=7KErFkvHGA8

19. NOISE FROM AN AUTOMATIC LOCKER, IS THIS NORMAL?
https://www.youtube.com/watch?v=Tv4Tba7gUC4

18. YUKON DURAGRIP POSITRACTION INSTALLATION WALKTHROUGH
https://www.youtube.com/watch?v=Ubf2qWYGotc

17. HOW TO IDENTIFY A GM 14 BOLT DIFFERENTIAL
https://www.youtube.com/watch?v=y3sXMW1CMVs

16. GEAR TOOTH PARTTERNS EXPLAINED
https://www.youtube.com/watch?v=C-srB9pUEE4

15. DECODING GM RPO CODES FOR YOUR DIFFERENTIAL
https://www.youtube.com/watch?v=dlSCxS7AB40

14. HOW TO PROPERLY GRIND A THICK RING GEAR TO CLEARANCE FOR THE CROSS PIN SHAFT
https://www.youtube.com/watch?v=dAyaY0R4PNg

13. HOW TO IDENTIFY FORD DIFFERENTIAL HOUSING TAGS
https://www.youtube.com/watch?v=90o5QtER-FI

12. YUKON SPIN FREE KIT INSTALLATION WALK THROUGH
https://www.youtube.com/watch?v=VM8OOreOytM

11. INSTALLING A GM 8.2 GEAR INTO A BUICK/OLDSMOBILE/PONTIAC HOUSING
https://www.youtube.com/watch?v=QvGsrxQNass

10. HOW TO IDENTIFY AND REDUCE POSITRACTION CHATTER
https://www.youtube.com/watch?v=JY2L-or4CAc

9. HOW TO STACK CLUTCHES IN A CLUTCH STYLE POSITRACTION
https://www.youtube.com/watch?v=z4TOL1X_aD8

8. HOW TO IDENTIFY DIFFERENTIAL GEAR NOISE, DECELERATION
https://www.youtube.com/watch?v=1OLfNz2nuDU

7. HOW TO BREAK IN A NEW GEAR SET
https://www.youtube.com/watch?v=Imoujpk4neg


6. HOW TO IDENTIFY GEAR RATIO
https://www.youtube.com/watch?v=ORdTuHnK7nA


5. HOW TO PROPERLY MEASURE A SEMIFLOAT AXLE
https://www.youtube.com/watch?v=BgO8LEsNrUY


4. HOW TO IDENTIFY 2 CUT VS. 5 CUT GEARS
https://www.youtube.com/watch?v=6lGIvOXVfcY


3. DRIVELINE MOVEMENT WITH AN AFTERMARKET LOCKER
https://www.youtube.com/watch?v=9na2biUPbZw


2. HOW TO MEASURE CARRIER DECK HEIGHT FOR GEAR RATIO CHANGE
https://www.youtube.com/watch?v=Ad1RoIksCg8


1. THE RIGHT GEAR OIL FOR A CLUTCH STYLE LIMITED SLIP DIFFERENTIAL
https://www.youtube.com/watch?v=_eqb6GfMy0o


Future videos will be posted here, where you can subscribe, https://www.youtube.com/user/YukonGear/videos every Tuesday until we run out of stuff to talk about.

TexasRedNeck:
Why do I get the feeling my head is about to hurt.....

TexasRedNeck:
You look a lot younger than I expected Tate!

I followed most of them but the 2 cut vs 5 cut.  Not sure I understood the heel/toe comments and why are there different types?  Pros/cons?  What is meant by the 2 cut or 5 cut? 

KensAuto:
One has 2 cuts, and the other one has 5. You. Are. Welcome.



fyi.

I will delete my dot posts when I'm done messing with Neck.....which may be a while.

TexasRedNeck:
thanks

Navigation

[0] Message Index

[#] Next page