Hello Guest

Author Topic: Getting a course on metal building construction  (Read 8657 times)

0 Members and 1 Guest are viewing this topic.

Offline Nate

  • Administrator
  • *****
  • Posts: 5051
    • View Profile
Re: Getting a course on metal building construction
« Reply #50 on: September 10, 2015, 12:11:01 AM »
Now that was great.  Very quiet launch.
Nate

Give me coffee for the things I can change and Bourbon for the things I cannot!

Offline Sammconn

  • A Guy in the Sticks
  • Registered
  • **
  • Posts: 3004
    • View Profile
Re: Getting a course on metal building construction
« Reply #51 on: September 10, 2015, 08:10:06 PM »
Pretty good, and quiet.
And it's not 'that' bad!
I just don't want to wind up missing a digit or limb.  I can sometimes get in a hurry to get results.
Sam

Offline Dawg25385

  • Registered
  • **
  • Posts: 2064
    • View Profile
Re: Getting a course on metal building construction
« Reply #52 on: September 10, 2015, 10:06:44 PM »
Epic...... I want one


Sent from my iPhone using Tapatalk
2006 Chevrolet 2500 HD 6.6 - MotorOps EFI, 4" MBRP, S&B intake, AirBags and B&W Turnover Ball
Prov 27:17, 2 Tim 1:7
NRA Life Member

Online TexasRedNeck

  • punching bag for moderator humor
  • Moderator
  • ***
  • Posts: 9622
    • View Profile
Re: Getting a course on metal building construction
« Reply #53 on: September 10, 2015, 11:54:03 PM »
I'll start a potato gun thread...

hmmm...

Humor and redneck practices or weapons....
Kids today don't know how easy they have it. When I was young, I had to walk 9 feet through shag carpet to change the TV channel.

Joshua 6:20-24

Offline cudakidd53

  • Moderator
  • ***
  • Posts: 3134
    • View Profile
Re: Getting a course on metal building construction
« Reply #54 on: September 14, 2015, 10:15:38 PM »
Creeping on your Dillon video RN- are you just trimming cases in that clip?
2012 Silverado LTZ - Duramax
Christian since 1975 - Field Trial Brittanys - NRA Lifetime Member

"When you're dead, you don't know you're dead. Hence, dealing with this fact is not difficult. It is only hard for those still living around you.....It's the same when you're stupid."

Online TexasRedNeck

  • punching bag for moderator humor
  • Moderator
  • ***
  • Posts: 9622
    • View Profile
Re: Getting a course on metal building construction
« Reply #55 on: September 14, 2015, 11:09:05 PM »
If thats the one I'm thinking of, yes.  I run them through the machine once to deprime, size and trim with the carbide cutter die and then after I prep a few thousand (including swaging the once fired mil stuff), I go back and prime, powder charge, seat and crimp.

I may look at the 1050 just because it has a swager station.  Swaging by hand is a PITA
« Last Edit: September 14, 2015, 11:10:50 PM by TexasRedNeck »
Kids today don't know how easy they have it. When I was young, I had to walk 9 feet through shag carpet to change the TV channel.

Joshua 6:20-24

Offline cudakidd53

  • Moderator
  • ***
  • Posts: 3134
    • View Profile
Re: Getting a course on metal building construction
« Reply #56 on: September 15, 2015, 08:39:16 PM »
Really like Dillon loaders- had one with the practice father-in-law....needless to say one of many things I lost!  Hope to get another someday for 9mm, .45, 5.56 and 30-06.  Really liked the quick change die heads; set-up once and change quickly as needed with minimal re-set time.  Dillon Dies are top notch too!
2012 Silverado LTZ - Duramax
Christian since 1975 - Field Trial Brittanys - NRA Lifetime Member

"When you're dead, you don't know you're dead. Hence, dealing with this fact is not difficult. It is only hard for those still living around you.....It's the same when you're stupid."